The functionality to flush the address translation table contains two bugs
which luckily compensate each other.
1. Just setting the operation is not sufficient to perform the flushing.
The "active" bit needs to be set to actually trigger an action.
For the vtu operations this is implemented correctly.
2. ar8xxx_phy_read_status is called every 2s by the phy state machine
to check for link changes. This would have caused an ATU flush
every 2s.
Fix the chip-specific ATU flush functions and remove the ATU flush call
from ar8xxx_phy_read_status.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44101 3c298f89-4303-0410-b956-a3cf2f4a3e73
AR8327/AR8337 allow to read the result of EEE autonegotiation.
If EEE is autonegotiated between the link partners, display
this as part of the swconfig get_link attribute.
eee100: 100MBit EEE supported by both link partners
eee1000: 1GBit EEE supported by both link partners
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44022 3c298f89-4303-0410-b956-a3cf2f4a3e73
Users reported network issues with AR8327 which turned out to be caused
by EEE not working correctly with certain link partners (ticket 14597).
The workaround was to disable EEE on all ports (changeset 41577).
The issue was with certain link partners only, therefore this patch
allows to control usage of EEE per port via swconfig.
Still the default is to initially disable EEE on all ports.
Successfully tested on a TL-WDR4900 (AR8327 rev.4)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44021 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move all AR8327/AR8337-specific driver code into a separate source file
ar8327.c and adjust patches so that ar8327.c is compiled if
CONFIG_AR8216_PHY is set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43845 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move several structure definitions and #defines from ar8216.c
to ar8216.h and move AR8327/AR8337 header stuff into a new
header file ar8327.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43844 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove read/write/rmw member functions from ar8xxx_priv
There seems to be no real benefit of the ar8xxx_priv member functions
read/write/rmw as one implementation exists for each of them only.
Especially ar8xxx_mii_rmw is assigned to priv->rmw first and then
mapped to ar8xxx_rmw.
Rename the ar8xxx_mii_.. functions to ar8xxx_.. and use them directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43742 3c298f89-4303-0410-b956-a3cf2f4a3e73
Create helpers mii_read32 / mii_write32 for 32 bit MII ops.
Rename r3 variable to page in ar8xxx_mii_write to make it consistent
with the other ar8xxx_mii_xxxx functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43741 3c298f89-4303-0410-b956-a3cf2f4a3e73
Factor out chip-specific parameters from ar8xxx_probe_switch.
Move the ar8xxx_chip definitions after the swops definitions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43740 3c298f89-4303-0410-b956-a3cf2f4a3e73
Factor out chip-specific data structures from ar8xxx_priv.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43469 3c298f89-4303-0410-b956-a3cf2f4a3e73
Factor out info whether switch should be configured at probe stage
to ar8xxx_chip. Remove related chip_is_... checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43466 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch reverts 43332 which seems to cause issues with VLAN functionality.
Add a specific check to check whether ANEG is still enabled and re-enable
it if necessary. Disable generic phy soft reset for kernel >=3.16.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43356 3c298f89-4303-0410-b956-a3cf2f4a3e73
We should make sure that also for ar8216 hw gets initialized.
For ar8216 hw_init is a dummy currently. The hw_init used for ar8236
should be generic enough to be usable with ar8216 too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43334 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move the PHY fixup call to the PHY init loop.
Use ar8xxx_has_gige in the PHY init instead of passing the gigE
capability via function parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43333 3c298f89-4303-0410-b956-a3cf2f4a3e73
Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set.
Fixes: ticket 17800
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43332 3c298f89-4303-0410-b956-a3cf2f4a3e73
PHY init code in the switch-specific hw_init functions is mainly
identical. Factor it out into a generic ar8xxx_phy_init function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43331 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move phy fixup code from the chip-specific hw_init functions into a
fixup_phys callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43330 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently there is a fixed 1000ms wait time after the switch was reset.
Most if not all switches need much less time to perform a reset.
Therefore replace the fixed wait time with polling for BMCR_RESET to
be cleared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43329 3c298f89-4303-0410-b956-a3cf2f4a3e73
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43328 3c298f89-4303-0410-b956-a3cf2f4a3e73
This allows tagged and untagged traffic together on the same port on ar8327
switch devices.
I looked at the first attempt to do this in r40777 (ar71xx: Fix tagged+untagged
operation on AR8327N (#12181)). I also set the vlan and port egress policies
like that change. But I change vlan_tagged in an less intrusive way. The
tagged/untagged decision is now based on the following rules:
- if vid != pvid then traffic is always tagged
- if vid == pvid then vlan_tagged stores if the traffic should be tagged
Tested on TP-Link WDR-3600 (ar8327N).
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42653 3c298f89-4303-0410-b956-a3cf2f4a3e73
This moves ingress, egress policy and pvid decisions to setup_port methods.
They arenow device type dependent.
This allows policy changes on only one device type which is needed to allow
tagged + untagged operation on ar8327.
Tested on TP-LINK WDR-3600 (ar8327N).
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42652 3c298f89-4303-0410-b956-a3cf2f4a3e73
Revert the tagged + untagged rework for now due to regressions in
vlan setup on certain AR83xx switches.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40842 3c298f89-4303-0410-b956-a3cf2f4a3e73
Replace the global "vlan_tagged" variable with an array storing the
tagging state per vlan.
The code was taken from #12181, tested and cleaned up by Saverio Proto
with additional bug fixes supplied by Álvaro Fernández.
Tested-by: Jo-Philipp Wich <jow@openwrt.org>
Signed-off-by: Saverio Proto <zioproto@gmail.com>
Signed-off-by: Álvaro Fernández <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40777 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be used for AR8327.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39337 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch enables jumbo frames on AR8327 switch by default.
I have tested it on TP-Link TL-WDR3600.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39076 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch is needed to use the switch inside the Sitecom WLR-8100;
it was unusable and detected as Generic-Phy before.
since ar8337 is behaving like ar8327
generally do the same thing
see: https://forum.openwrt.org/viewtopic.php?pid=214218#p214218
forward-ported to trunk
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4469/
[juhosg: merge chip_is_ar83[23]7 statements in ar8xxx_phy_config_init]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38952 3c298f89-4303-0410-b956-a3cf2f4a3e73
Tested on Buffalo WZR-600DHP with ar8316 switch. Commands used to mirror both
RX and TX traffic from LAN port 1 to LAN port 4:
$ swconfig dev switch0 set enable_mirror_rx 1
$ swconfig dev switch0 set enable_mirror_tx 1
$ swconfig dev switch0 set mirror_monitor_port 4
$ swconfig dev switch0 set mirror_source_port 1
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36713 3c298f89-4303-0410-b956-a3cf2f4a3e73
The AR8327 switch gets its configuration from platform
data or from the device-tree. This allows to start it
from the probe routine. Doing so makes it usable with
ethernet drivers which only connects to the PHY device
when the ethernet interface is opened.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36050 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move switch starting code into a separate function.
This makes it usable from other places.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36049 3c298f89-4303-0410-b956-a3cf2f4a3e73
